[{"data":1,"prerenderedAt":65},["ShallowReactive",2],{"blog-clock-supply-noise-jitter-validation-en":3},{"title":4,"description":5,"date":6,"lastUpdated":6,"category":7,"image":8,"imageAlt":9,"readingTime":10,"wordCount":11,"timeRequired":12,"htmlContent":13,"faq":14,"tags":30,"slug":34,"sourceLocale":35,"availableLocales":36,"jsonld":41},"Clock Supply Noise and Jitter: A Validation Guide","Diagnose clock supply noise with matched rail and clock measurements, frequency-dependent sensitivity, safe injection checks and a traceable validation plan.","2026-11-18","testing","/assets/blogs/clock-supply-noise-jitter-validation/measurement-evidence.svg","Evidence records for regulator input, local clock supply, controlled disturbance and clock output measurements",14,2773,"PT14M","\u003Cp>\u003Cstrong>Start by measuring the clock and its actual supply rail under representative conditions, then change one suspected coupling path at a time.\u003C/strong> If a rail disturbance is responsible, a controlled change should produce a repeatable, frequency-dependent change in the clock’s phase or timing behavior. A spectral peak on the rail and a peak at the same clock offset are a useful lead—not proof of causation.\u003C/p>\n\u003Cp>The decision is not simply whether the rail looks noisy. It is whether noise reaches the clock at frequencies where that particular device is sensitive, and whether another path can explain the result. Regulator input noise, regulator self-noise, downstream impedance, dynamic loads, reference inputs, output loading and the measurement setup all deserve separate tests.\u003C/p>\n\u003Cp>Define the required jitter metric and operating conditions first. Then use the following matrix to choose the next measurement rather than adding components blindly.\u003C/p>\n\u003Ch2>Symptom-to-test-to-evidence matrix\u003C/h2>\n\u003Ctable>\n\u003Cthead>\n\u003Ctr>\n\u003Cth>Observation\u003C/th>\n\u003Cth>Next test\u003C/th>\n\u003Cth>Evidence that would strengthen the hypothesis\u003C/th>\n\u003C/tr>\n\u003C/thead>\n\u003Ctbody>\u003Ctr>\n\u003Ctd>Clock phase spur has the same offset as a rail ripple peak\u003C/td>\n\u003Ctd>Measure the rail near the clock; change the suspected disturbance while holding other conditions constant\u003C/td>\n\u003Ctd>The measured rail tone and phase spur change together and return toward baseline when the change is removed\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Clock worsens when an upstream converter changes operating mode\u003C/td>\n\u003Ctd>Record regulator input, clock rail and clock output in each mode; where safe, perturb or substitute the upstream source\u003C/td>\n\u003Ctd>The upstream change produces a corresponding rail change and repeatable clock response; alternative reference and load effects are checked\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Clock is poor even with a quiet regulator input\u003C/td>\n\u003Ctd>Compare output-rail noise with input conditions held stable; investigate regulator noise and downstream loading\u003C/td>\n\u003Ctd>Output-rail behavior changes with the regulator or its operating point without a comparable input disturbance; this narrows the cause but does not isolate self-noise by itself\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Jitter changes with system activity or output loading\u003C/td>\n\u003Ctd>Toggle one load or clock-output condition at a time; observe local rail and output waveform\u003C/td>\n\u003Ctd>A repeatable activity-dependent rail disturbance and clock change occur together; output loading and reference changes are separately ruled out\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>A proposed filter lowers one rail peak but jitter does not improve\u003C/td>\n\u003Ctd>Compare the complete relevant rail spectrum and phase-noise spectrum before and after\u003C/td>\n\u003Ctd>The remaining noise lies outside the filter’s effective band, the clock is more sensitive elsewhere, or a non-supply path dominates\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>A peak appears only with a particular probe or connection\u003C/td>\n\u003Ctd>Change the measurement arrangement and assess the instrument floor\u003C/td>\n\u003Ctd>The feature moves or disappears with the probe, grounding or instrument setup rather than with the DUT operating condition\u003C/td>\n\u003C/tr>\n\u003C/tbody>\u003C/table>\n\u003Cp>A load change can affect the rail and output waveform simultaneously, so a second comparison may be needed to separate those effects. Similarly, a spectral line or jitter correlation at a regulator’s switching frequency does not by itself establish the cause. Consider other signals, harmonics and aliases, probe or fixture coupling, common references, clocking modes and return paths. Change one condition or use an independent measurement, then compare the result with the hypothesis. Crosstalk and data-correlated jitter depend on the configuration and cannot be bounded universally from one trace. Record the conditions and measurement setup so the observation can be reproduced.\u003C/p>\n\u003Ch2>Separate the paths before choosing a remedy\u003C/h2>\n\u003Cp>A clock rail can be disturbed through several mechanisms:\u003C/p>\n\u003Cul>\n\u003Cli>\u003Cstrong>Regulator input noise:\u003C/strong> Switching ripple or other upstream noise can pass through the regulator. Its power-supply rejection ratio, or PSRR, describes input-to-output disturbance transfer under specified conditions. Check the source’s sign convention, frequency, input and output voltage, load and test setup.\u003C/li>\n\u003Cli>\u003Cstrong>Regulator self-noise:\u003C/strong> Even with a quiet input, a regulator contributes output noise. PSRR alone does not quantify it. Comparing regulators or operating points can help, but differences in output impedance and stability may also affect the result.\u003C/li>\n\u003Cli>\u003Cstrong>Downstream impedance and dynamic current:\u003C/strong> Current changes flowing through the regulator, traces, planes and local network create voltage changes at the clock. A quiet regulator output measured elsewhere does not guarantee a quiet DUT pin.\u003C/li>\n\u003Cli>\u003Cstrong>Other paths:\u003C/strong> A reference source or PLL input can carry phase noise into the output. Output termination, receiver loading, signal integrity, crosstalk and the measurement chain can also change the observed result.\u003C/li>\n\u003C/ul>\n\u003Cp>These paths can coexist. A shared disturbance can be correlated across them, so do not automatically add every contribution as independent noise. Likewise, do not use regulator PSRR as a substitute for the clock’s own supply sensitivity.\u003C/p>\n\u003Cp>For broader board-level preparation, use the \u003Ca href=\"/en/blog/power-integrity-checklist-pcb-design-basics/\">power integrity checklist\u003C/a>. For reference and distribution issues beyond the supply test, see the \u003Ca href=\"/en/blog/clock-tree-layout-tutorial-pcb-design-basics/\">clock tree layout tutorial\u003C/a>.\u003C/p>\n\u003Ch2>Establish a baseline at the DUT\u003C/h2>\n\u003Cp>Record the device, board revision, supply settings, reference source, clock carrier, output format and termination. Set representative system activity, temperature and loads. Choose the offset-frequency range and timing metric from the actual design requirement; there is no universal jitter integration band or acceptance limit.\u003C/p>\n\u003Cp>With no added disturbance:\u003C/p>\n\u003Col>\n\u003Cli>Measure the clock output and retain its phase-noise spectrum and any relevant timing results.\u003C/li>\n\u003Cli>Measure the DC level and AC rail behavior as close as practical to the clock supply pin and its return.\u003C/li>\n\u003Cli>Record the regulator input and relevant load states when they may be part of the hypothesis.\u003C/li>\n\u003Cli>Save instrument settings, bandwidths, reference configuration and raw data so the comparison can be repeated.\u003C/li>\n\u003C/ol>\n\u003Cp>The rail measurement is \u003Cstrong>not\u003C/strong> necessarily the same as the generator setting or a reading at the regulator. Bypass networks, interconnect and loading change the signal reaching the DUT. Teledyne LeCroy’s clock jitter sensitivity measurement example illustrates how loading and bypass capacitance can alter a rail perturbation; its particular setup is not a general fixture recommendation.\u003C/p>\n\u003Cp>Check the probe as part of the circuit. Its capacitance, resistance, return connection and bandwidth can change or misrepresent the rail. Use a suitable probing method and compare results with an alternative arrangement where practical. Verify voltage range, grounding and common-mode limits before connecting anything.\u003C/p>\n\u003Cp>Also establish the \u003Cstrong>measurement floor\u003C/strong> for the relevant setup. If the instrument, reference or probe noise masks the DUT, a small improvement may be invisible. Document the floor and uncertainty rather than treating every displayed feature as device noise.\u003C/p>\n\u003Cp>For RMS PCB or interface jitter, root-sum-square (RSS) subtraction is appropriate only when the instrument floor is independently characterized under comparable conditions, with compatible bandwidth and filtering, and is sufficiently separated from the device result. The calculation assumes appropriately uncorrelated contributions; deterministic, correlated or coupled effects do not generally disappear through subtraction. Carry uncertainty through the calculation and report the raw result, floor characterization, assumptions and repeatability. Label the corrected value as an estimate.\u003C/p>\n\u003Cdiv data-component=\"BlogQuickQuoteInline\">\u003C/div>\n\n\u003Ch2>Keep the reported quantities distinct\u003C/h2>\n\u003Ctable>\n\u003Cthead>\n\u003Ctr>\n\u003Cth>Quantity\u003C/th>\n\u003Cth>What to report and how to interpret it\u003C/th>\n\u003C/tr>\n\u003C/thead>\n\u003Ctbody>\u003Ctr>\n\u003Ctd>\u003Cstrong>Regulator PSRR\u003C/strong>\u003C/td>\n\u003Ctd>Frequency-dependent input-to-output disturbance rejection, with the definition, operating point and sign convention. It does not include every downstream noise mechanism.\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>\u003Cstrong>Clock supply sensitivity\u003C/strong>\u003C/td>\n\u003Ctd>The clock response to a defined disturbance measured at the DUT rail, at a stated frequency and operating condition. The output quantity might be a phase spur, phase deviation or timing variation.\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>\u003Cstrong>Discrete phase spur\u003C/strong>\u003C/td>\n\u003Ctd>A narrow phase-modulation component relative to carrier power, normally reported in \u003Cstrong>dBc\u003C/strong>, with its offset and measurement method. Confirm that the instrument is measuring phase modulation rather than confusing it with amplitude modulation.\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>\u003Cstrong>Broadband phase noise\u003C/strong>\u003C/td>\n\u003Ctd>Noise density versus offset from the carrier, normally in \u003Cstrong>dBc/Hz\u003C/strong>. A discrete spur height in dBc is not a broadband density and must not be integrated as though it were one. Depending on the analysis convention, its contribution can be included separately as power; report whether and how spurs are included.\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>\u003Cstrong>TIE\u003C/strong>\u003C/td>\n\u003Ctd>Time-interval error: edge displacement relative to a defined reference or recovered clock. State the reference and measurement configuration.\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>\u003Cstrong>Period jitter\u003C/strong>\u003C/td>\n\u003Ctd>Variation of individual clock periods relative to the defined nominal or mean period. It is not interchangeable with TIE.\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>\u003Cstrong>Integrated RMS jitter\u003C/strong>\u003C/td>\n\u003Ctd>A timing result derived over a stated phase-noise offset band. Report carrier frequency, integration limits, processing conventions and whether discrete spurs are included.\u003C/td>\n\u003C/tr>\n\u003C/tbody>\u003C/table>\n\u003Cp>An integrated phase-noise result depends on the offset-frequency limits, detector or filter response, carrier or clock architecture, units and conversion model. Record the carrier frequency, spectral convention, treatment of deterministic spurs, instrument response, reference-plane effects and assumptions used to convert phase fluctuations to time jitter. A result from one band is not automatically comparable to, or a compliance result for, another clocking mode or specification. Changing the integration limits or filtering can change the result even when the source is unchanged.\u003C/p>\n\u003Cp>DJ + 2Q × RJ is a model-dependent dual-Dirac extrapolation; RJ denotes the fitted random-jitter standard deviation. Comparisons require the fitted deterministic jitter, assumed random-jitter distribution, Q or tail convention, BER target, transition selection, instrument bandwidth and filtering, and measurement method. A finite capture’s peak-to-peak range is a sample-quantile span affected by record length, correlation and selection. Extrapolating fitted tails to a very low BER is not equivalent to capturing that many independent edges; its validity depends on how well the model represents the signal.\u003C/p>\n\u003Cp>“PSNR” needs special care: sources use the label for different supply-noise-rejection definitions. To make a result reproducible, report:\u003C/p>\n\u003Cul>\n\u003Cli>The original equation or transfer definition and its sign convention.\u003C/li>\n\u003Cli>The stimulus quantity and amplitude convention, such as RMS, peak, peak-to-peak or power.\u003C/li>\n\u003Cli>The output quantity and the impedance assumptions.\u003C/li>\n\u003Cli>The clock carrier, disturbance offset and measurement bandwidth.\u003C/li>\n\u003C/ul>\n\u003Cp>A dB value derived from stimulus and spur power is not interchangeable with an LDO’s PSRR or a general ps/mV sensitivity. Do not assume a universal conversion between them. For an example, consult the definition and stimulus in Rohde &amp; Schwarz Application Card PD 3608.6190.92, version 02.00, “Measuring power supply induced jitter and PSNR in low jitter oscillators and clocks.”\u003C/p>\n\u003Cp>\u003Cimg src=\"/assets/blogs/clock-supply-noise-jitter-validation/measurement-evidence.svg\" alt=\"Evidence records for regulator input, local clock supply, controlled disturbance and clock output measurements\">\u003C/p>\n\u003Cp>The arrows show comparisons between measurement records, not electrical wiring or an injector circuit.\u003C/p>\n\u003Ch2>Test coupling across frequency\u003C/h2>\n\u003Cp>A useful diagnostic asks: \u003Cstrong>for a disturbance actually present at the clock rail, how does the clock respond at each relevant frequency?\u003C/strong> A single result at one offset cannot characterize the whole band.\u003C/p>\n\u003Cp>Controlled injection is only for \u003Cstrong>qualified designers\u003C/strong>. For a valid characterization, the operating point and complete supply waveform must meet the device’s specified recommended operating conditions for the intended measurement. Separately, startup, peaks and transients at the supply pin relative to its local return must never exceed the device’s absolute-maximum ratings. Absolute-maximum ratings are survival boundaries, not valid measurement conditions or targets. Check and record current, power, injection-network and instrument-port limits separately. Protect instrument ports from DC where the chosen topology requires it; do not connect a 50 Ω instrument input directly across a powered rail. Skyworks application note AN491 discusses AC injection, DC isolation and the drive demands of a low-impedance rail.\u003C/p>\n\u003Cp>A repeatable plan is:\u003C/p>\n\u003Col>\n\u003Cli>\u003Cstrong>Measure injection off.\u003C/strong> Save the baseline rail spectrum and clock phase-noise or timing result.\u003C/li>\n\u003Cli>\u003Cstrong>Apply a small, known disturbance safely.\u003C/strong> Measure its actual amplitude and waveform near the DUT relative to the local return, including the DC level and injection peaks. State whether amplitude is RMS, peak or peak-to-peak.\u003C/li>\n\u003Cli>\u003Cstrong>Observe the clock at the corresponding offset.\u003C/strong> A sinusoidal rail tone may produce clock sidebands at the carrier plus and minus the disturbance frequency. Identify the phase component and note any pre-existing spur.\u003C/li>\n\u003Cli>\u003Cstrong>Repeat at selected offsets and safe amplitudes.\u003C/strong> Verify the actual rail level at each point; the delivered level can vary with frequency. More than one amplitude helps reveal whether a small-signal proportional assumption is reasonable.\u003C/li>\n\u003Cli>\u003Cstrong>Turn the disturbance off and repeat.\u003C/strong> Check whether rail and clock results return toward baseline. Repeat the sequence to assess drift and repeatability.\u003C/li>\n\u003Cli>\u003Cstrong>Test a separate intervention.\u003C/strong> Change the suspected source, load or supply path while preserving the other conditions as closely as possible. Check reference and output paths if the intervention also affects them.\u003C/li>\n\u003C/ol>\n\u003Cp>The resulting curve is a \u003Cstrong>device-and-configuration-specific sensitivity\u003C/strong>, not a universal component property. Texas Instruments oscillator application note SNAA399 reports different induced spurs across ripple frequencies for specified oscillator test conditions; its results should not be transferred to another clock or board without validation.\u003C/p>\n\u003Cp>A pre-existing coherent spur complicates comparisons: its phase can affect the observed combined result, so subtracting displayed dBc values is not generally a valid way to isolate the injected contribution. For broadband prediction, a small-signal transfer model also needs compatible spectral conventions and treatment of correlated sources. A tone measurement alone does not establish broadband RMS jitter.\u003C/p>\n\u003Ch2>Validate the proposed change, not just the rail\u003C/h2>\n\u003Cp>Once a path is supported by evidence, select a candidate intervention for the frequency band and operating condition involved. It might address the upstream source, regulator, local network, dynamic load, reference or output interface.\u003C/p>\n\u003Cp>A bead, LDO or capacitor is \u003Cstrong>not\u003C/strong> a guaranteed jitter improvement. A network can attenuate one band while peaking at another. A regulator or output network can also introduce stability, current, startup or transient concerns. Evaluate the complete proposed configuration against device documentation and design requirements.\u003C/p>\n\u003Cp>Compare before and after with the same:\u003C/p>\n\u003Cul>\n\u003Cli>Carrier, reference, output termination and system load.\u003C/li>\n\u003Cli>Supply operating point and relevant environmental conditions.\u003C/li>\n\u003Cli>Probe location, instrument setup, bandwidth and analysis method.\u003C/li>\n\u003Cli>Phase-noise integration band and spur-inclusion convention.\u003C/li>\n\u003C/ul>\n\u003Cp>Measure both the rail and clock. Check the relevant frequency range for new resonance or noise peaks, and assess startup, transient voltage, regulator stability and component ratings. A lower rail peak is useful evidence, but the remedy succeeds only if the required clock metric meets the project’s stated requirement under representative conditions.\u003C/p>\n\u003Ch2>Measurement handoff checklist\u003C/h2>\n\u003Cp>Give the next designer or test team enough information to reproduce the conclusion:\u003C/p>\n\u003Cul>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> DUT identity, board revision, supply rail and schematic or measurement-point references.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Clock carrier, output format, termination, reference source and PLL configuration.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Supply settings, system activity, loads, temperature and other relevant operating conditions.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Required metric and acceptance criterion from the project or device requirement—not an assumed generic limit.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Rail probe point, return path, probe characteristics, bandwidth and loading assessment.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Instrument configuration, reference, floor, calibration status where applicable, and uncertainty or known limitations.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Baseline rail and clock data, including raw spectra and timing captures.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Intervention or injection method, safety review, actual DUT-rail amplitude, frequency and amplitude convention.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> For injection: recommended operating conditions and absolute-maximum checks, plus separate current, power, injection-network and instrument-port limits.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Before/after results, repeatability, phase-versus-amplitude discrimination, and any unresolved alternative paths.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> For integrated RMS jitter: carrier, offset limits, processing and treatment of spurs.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> For PSNR: original equation or transfer definition, sign convention, stimulus quantity and amplitude convention, output quantity, impedance assumptions, carrier, offset and measurement bandwidth.\u003C/li>\n\u003C/ul>\n\u003Cp>For PCB manufacturing or \u003Ca href=\"/en/products/pcb-assembly/\">PCB assembly (PCBA)\u003C/a>, \u003Ca href=\"/en/quote/\">request a quote\u003C/a> with the fabrication files, assembly drawing, BOM, placement data, quantities and applicable inspection requirements. Include the revised design requirements and agree on the manufacturing and test scope for the project.\u003C/p>\n\u003C!-- faq:start -->\n\n\u003Ch2>FAQ\u003C/h2>\n\u003Ch3>Can matching rail and clock spectral peaks prove supply coupling?\u003C/h3>\n\u003Cp>No. They identify a candidate frequency. A controlled intervention, measurement of the actual DUT rail, a repeatable clock response and checks of reference, output and measurement paths provide stronger evidence.\u003C/p>\n\u003Ch3>Is a low-noise regulator enough to protect a clock?\u003C/h3>\n\u003Cp>Not necessarily. Regulator input rejection, self-noise, downstream impedance and dynamic current all matter, as does the clock’s sensitivity at each frequency. Validate the assembled circuit under its intended load.\u003C/p>\n\u003Ch3>Why measure the injected ripple at the clock pin?\u003C/h3>\n\u003Cp>The generator setting does not account for all loading and frequency-dependent behavior between the source and DUT. Measuring near the pin establishes the disturbance the clock actually experiences, subject to probe accuracy and loading.\u003C/p>\n\u003Ch3>Can one supply-injection tone predict integrated RMS jitter?\u003C/h3>\n\u003Cp>Not by itself. A tone probes response at a particular frequency and amplitude. Broadband prediction requires a valid frequency-dependent model, the rail spectrum, compatible noise conventions and appropriate treatment of correlations and discrete spurs.\u003C/p>\n\u003Ch3>What if the rail improves but the clock does not?\u003C/h3>\n\u003Cp>Check whether the improvement occurred in a frequency band to which the clock is sensitive, whether another rail feature or resonance remains, and whether reference, output load or measurement noise dominates. Repeat under matched conditions before selecting another remedy.\u003C/p>\n\u003C!-- faq:end -->\n\u003Csection class=\"related-links\" aria-label=\"Related\">\u003Ch3>Related links\u003C/h3>\u003Cul>\u003Cli>\u003Ca href=\"/en/blog/power-integrity-checklist-pcb-design-basics/\">power integrity checklist: a practical PCB design basics guide from concept to layout\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/blog/clock-tree-layout-tutorial-pcb-design-basics/\">Clock tree layout tutorial: Common PCB design issues and a practical checklist\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/products/pcb-assembly/\">PCB assembly (PCBA)\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/quote/\">request a quote\u003C/a>\u003C/li>\u003C/ul>\u003C/section>",[15,18,21,24,27],{"question":16,"answer":17,"answerText":17},"Can matching rail and clock spectral peaks prove supply coupling?","No. They identify a candidate frequency. A controlled intervention, measurement of the actual DUT rail, a repeatable clock response and checks of reference, output and measurement paths provide stronger evidence.",{"question":19,"answer":20,"answerText":20},"Is a low-noise regulator enough to protect a clock?","Not necessarily. Regulator input rejection, self-noise, downstream impedance and dynamic current all matter, as does the clock’s sensitivity at each frequency. Validate the assembled circuit under its intended load.",{"question":22,"answer":23,"answerText":23},"Why measure the injected ripple at the clock pin?","The generator setting does not account for all loading and frequency-dependent behavior between the source and DUT. Measuring near the pin establishes the disturbance the clock actually experiences, subject to probe accuracy and loading.",{"question":25,"answer":26,"answerText":26},"Can one supply-injection tone predict integrated RMS jitter?","Not by itself. A tone probes response at a particular frequency and amplitude. Broadband prediction requires a valid frequency-dependent model, the rail spectrum, compatible noise conventions and appropriate treatment of correlations and discrete spurs.",{"question":28,"answer":29,"answerText":29},"What if the rail improves but the clock does not?","Check whether the improvement occurred in a frequency band to which the clock is sensitive, whether another rail feature or resonance remains, and whether reference, output load or measurement noise dominates. Repeat under matched conditions before selecting another remedy.",[31,32,33],"clock jitter","power supply noise","phase noise","clock-supply-noise-jitter-validation","en",[35,37,38,39,40],"de","cn","fr","ru",{"blog":42,"breadcrumb":51},{"@context":43,"@type":44,"headline":4,"description":5,"image":8,"url":45,"datePublished":6,"dateModified":6,"timeRequired":12,"keywords":46,"articleSection":7,"author":47,"publisher":50},"https://schema.org","BlogPosting","https://hilpcb.com/en/blog/clock-supply-noise-jitter-validation/","clock jitter, power supply noise, phase noise",{"@type":48,"name":49},"Organization","HILPCB",{"@type":48,"name":49},{"@context":43,"@type":52,"itemListElement":53},"BreadcrumbList",[54,59,63],{"@type":55,"position":56,"name":57,"item":58},"ListItem",1,"Home","https://hilpcb.com/",{"@type":55,"position":60,"name":61,"item":62},2,"Blog","https://hilpcb.com/en/blog/",{"@type":55,"position":64,"name":34,"item":45},3,1795020490331]