[{"data":1,"prerenderedAt":66},["ShallowReactive",2],{"blog-led-indicator-series-resistor-calculation-en":3},{"title":4,"description":5,"date":6,"lastUpdated":6,"category":7,"image":8,"imageAlt":9,"readingTime":10,"wordCount":11,"timeRequired":12,"htmlContent":13,"faq":14,"tags":30,"slug":34,"sourceLocale":35,"availableLocales":36,"jsonld":42},"LED Indicator Resistor: Tolerance and Current Validation","Calculate an LED indicator resistor, check supply and component tolerances, and validate current, resistor power and visibility on assembled boards.","2026-11-11","design","/assets/blogs/led-indicator-series-resistor-calculation/led-indicator-series-circuit.svg","Conceptual low-voltage DC circuit with one resistor and one LED in series",13,2582,"PT13M","\u003Cp>A series resistor is a simple way to set an initial operating current for one low-voltage DC indicator LED. The calculation is short, but the result is only a starting point: supply voltage, LED behavior, resistor tolerance, temperature, and the output driving the circuit can all change the actual current.\u003C/p>\n\u003Cp>This guide follows the calculation through current corners, resistor dissipation, driver limits and checks on an assembled board. Its numerical example is entirely fictional. It applies to one low-voltage DC indicator LED in one series path; it does not cover AC or mains circuits, parallel LEDs sharing a resistor, or safety-function design.\u003C/p>\n\u003Ch2>Start with the series circuit\u003C/h2>\n\u003Cp>A basic indicator circuit has a DC source, a resistor, and one LED in a single current path:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">Positive supply ── resistor ── LED ── return\n\u003C/code>\u003C/pre>\n\u003Cp>The LED must be oriented for forward conduction. Because the components are in series, the same current flows through the resistor and LED. The resistor limits that current by dropping some of the available voltage.\u003C/p>\n\u003Cp>Kirchhoff’s voltage law, or KVL, says that the voltage rises and drops around the closed loop add to zero. For this simple circuit:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">VS = VR + VF\n\u003C/code>\u003C/pre>\n\u003Cp>Where:\u003C/p>\n\u003Cul>\n\u003Cli>\u003Ccode>VS\u003C/code> is the voltage available across the resistor and LED.\u003C/li>\n\u003Cli>\u003Ccode>VR\u003C/code> is the voltage across the resistor.\u003C/li>\n\u003Cli>\u003Ccode>VF\u003C/code> is the LED’s forward voltage at the operating current.\u003C/li>\n\u003C/ul>\n\u003Cp>\u003Ca href=\"/en/blog/ohms-law/\">Ohm’s law\u003C/a> gives \u003Ccode>VR = I × R\u003C/code>. Combining the relationships gives the familiar starting equation:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">R = (VS − VF) / I\n\u003C/code>\u003C/pre>\n\u003Cp>Use volts for voltage and amperes for current to obtain resistance in ohms. For example, 5 mA is 0.005 A.\u003C/p>\n\u003Cp>This equation describes an operating point; it does not make \u003Ccode>VF\u003C/code> a fixed property. LED forward voltage changes with current and temperature, and individual devices vary. Choose a target current based on the actual LED, required visibility, and driver limits—not on an assumed current that is supposedly right for every indicator.\u003C/p>\n\u003Ch2>A fully fictional example\u003C/h2>\n\u003Cp>Suppose a project uses a fictional LED and an ideal voltage source. The design team makes these \u003Cstrong>illustrative assumptions\u003C/strong>, not claims about a real component:\u003C/p>\n\u003Ctable>\n\u003Cthead>\n\u003Ctr>\n\u003Cth>Input\u003C/th>\n\u003Cth align=\"right\">Fictional assumption\u003C/th>\n\u003C/tr>\n\u003C/thead>\n\u003Ctbody>\u003Ctr>\n\u003Ctd>Nominal supply\u003C/td>\n\u003Ctd align=\"right\">5.00 V\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Supply range\u003C/td>\n\u003Ctd align=\"right\">4.75 V to 5.25 V\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>LED voltage at the intended nominal current\u003C/td>\n\u003Ctd align=\"right\">2.00 V\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Initial target current\u003C/td>\n\u003Ctd align=\"right\">5.00 mA\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>LED voltage used for the later corner exercise\u003C/td>\n\u003Ctd align=\"right\">1.80 V to 2.20 V at the resulting operating points\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Intended current window\u003C/td>\n\u003Ctd align=\"right\">4.00 mA to 6.00 mA\u003C/td>\n\u003C/tr>\n\u003C/tbody>\u003C/table>\n\u003Cp>Start with the nominal values:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">R = (5.00 V − 2.00 V) / 0.005 A\n  = 600 Ω\n\u003C/code>\u003C/pre>\n\u003Cp>The calculation asks for 600 Ω. Suppose the project’s available standard-value choice is \u003Cstrong>620 Ω\u003C/strong>, with a fictional ±1% resistance limit for the conditions being evaluated. Selecting the next higher available value reduces the estimated current relative to the 600 Ω calculation.\u003C/p>\n\u003Cp>Using the same assumed 2.00 V LED drop, the nominal current with 620 Ω is:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">I = (5.00 V − 2.00 V) / 620 Ω\n  ≈ 0.00484 A\n  ≈ 4.84 mA\n\u003C/code>\u003C/pre>\n\u003Cp>The result is near the initial 5.00 mA target, not exactly equal to it. Whether 4.84 mA provides the desired visibility still depends on the actual LED and application.\u003C/p>\n\u003Ch3>Calculate nominal resistor power\u003C/h3>\n\u003Cp>At the nominal operating point, the resistor drops 3.00 V. Its nominal dissipation is:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">P = VR² / R\n  = 3.00² / 620\n  ≈ 0.0145 W\n  = 14.5 mW\n\u003C/code>\u003C/pre>\n\u003Cp>The equivalent calculation is \u003Ccode>P = I²R\u003C/code>, using the same current and resistance. This is \u003Cstrong>nominal power\u003C/strong>, not the highest possible dissipation and not a resistor rating.\u003C/p>\n\u003Cp>For a real selection, compare the applicable worst-case dissipation with the rating and derating information for the exact resistor, its mounting, and its thermal environment. A suitable standard resistance value alone does not establish a suitable component.\u003C/p>\n\u003Ch2>Check the assumed high- and low-current corners\u003C/h2>\n\u003Cp>For the fictional example, suppose the ±1% resistance limits are assumed to hold throughout the conditions under review:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">Minimum resistance = 620 Ω × 0.99 = 613.8 Ω\nMaximum resistance = 620 Ω × 1.01 = 626.2 Ω\n\u003C/code>\u003C/pre>\n\u003Cp>Using the fictional LED-voltage boundaries from the table, the high-current calculation combines maximum supply, minimum assumed LED voltage, and minimum resistance:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">Ihigh = (5.25 V − 1.80 V) / 613.8 Ω\n      ≈ 5.62 mA\n\u003C/code>\u003C/pre>\n\u003Cp>The low-current calculation combines minimum supply, maximum assumed LED voltage, and maximum resistance:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">Ilow = (4.75 V − 2.20 V) / 626.2 Ω\n     ≈ 4.07 mA\n\u003C/code>\u003C/pre>\n\u003Cp>Under these assumptions, the calculated current envelope is approximately \u003Cstrong>4.07 mA to 5.62 mA\u003C/strong>, within the fictional 4.00 mA to 6.00 mA window. The calculation does not prove that a real circuit meets that window: the LED voltage limits, resistance limits, ideal source, and current requirement were invented for the exercise.\u003C/p>\n\u003Cp>The corresponding high-corner resistor power estimate is:\u003C/p>\n\u003Cpre>\u003Ccode class=\"language-text\">Phigh = (5.25 V − 1.80 V)² / 613.8 Ω\n      ≈ 0.0194 W\n      = 19.4 mW\n\u003C/code>\u003C/pre>\n\u003Cp>That is higher than the 14.5 mW nominal estimate. It still needs to be compared with an exact resistor’s allowable dissipation under the intended conditions. A real driver’s voltage drop, resistance changes with temperature, and other circuit losses may also need to be included.\u003C/p>\n\u003Cp>The corners are useful only if their assumed bounds cover the actual operating conditions. Forward voltage and current are interdependent: the LED’s voltage is determined by its current-voltage behavior, not by an independent fixed-voltage source. Use applicable guaranteed limits and curves, circuit modeling, or measurements as appropriate. A conservative envelope need not imply that every extreme combination will actually occur.\u003C/p>\n\u003Ch2>Understand what an LED datasheet does—and does not—guarantee\u003C/h2>\n\u003Cp>Datasheet values must be read with their test conditions. For example, the Kingbright \u003Cstrong>APT1608EC\u003C/strong> datasheet, revision V.18A, lists a forward voltage of \u003Cstrong>2 V typical and 2.5 V maximum at 20 mA and 25 °C\u003C/strong>. Those numbers are not universal operating extremes at every current and temperature. The 20 mA condition is a measurement condition, not a requirement to run the indicator at 20 mA. Check the current revision for the actual part before design release.\u003C/p>\n\u003Cp>That datasheet does not provide a guaranteed forward-voltage minimum covering the intended current, temperature, and production range. In particular, the 2 V typical value is not a minimum. Without a justified lower boundary, it cannot by itself establish a guaranteed maximum-current corner for the series-resistor circuit.\u003C/p>\n\u003Cp>If the necessary boundary is missing, seek supplier clarification, characterize representative parts, or adopt a documented project assumption with appropriate engineering margin. Measurements and assumptions can inform a design, but they do not automatically become supplier guarantees across all future production. Revisit the analysis if the LED, operating range, or available evidence changes.\u003C/p>\n\u003Cp>Also distinguish a test condition from a limit. The APT1608EC datasheet lists an absolute maximum DC forward current of 30 mA at 25 °C; operation at other temperatures requires the applicable derating information. An absolute maximum is not a recommended brightness target. Check the exact device’s continuous and, where relevant, pulse limits together with its thermal conditions.\u003C/p>\n\u003Ch2>Select a resistor for more than its nominal value\u003C/h2>\n\u003Cp>Available resistance values come in standard series, and a supplier’s actual offerings may differ by tolerance and product family. After calculating the nominal value:\u003C/p>\n\u003Col>\n\u003Cli>Identify available values near it.\u003C/li>\n\u003Cli>Calculate current using the value selected.\u003C/li>\n\u003Cli>Check both excessive-current and insufficient-visibility conditions.\u003C/li>\n\u003Cli>Select an exact resistor with appropriate tolerance, voltage, power, temperature, and stability characteristics.\u003C/li>\n\u003C/ol>\n\u003Cp>Rounding upward is often a reasonable first move when current must not exceed a target. It is not an automatic final answer: a larger resistor may make the indicator too dim at minimum supply. Rounding downward increases current and needs the corresponding limit checks.\u003C/p>\n\u003Cp>Tolerance describes an allowed resistance variation under specified conditions. It is not necessarily a complete allowance for temperature coefficient, soldering, aging, humidity, or other changes. Decide which effects matter over the product’s life, then use the exact part’s documentation.\u003C/p>\n\u003Cp>For example, Vishay’s D/CRCW e3 datasheet, revision 14 April 2026, lists ratings for particular resistor families and operating modes. Its CRCW0603 standard and extended operation ratings have different conditions and stability expectations. Neither a package size nor that example establishes the power rating of every resistor in that size. Verify the exact part, rating temperature, permitted film temperature, mounting, board thermal path, and applicable derating.\u003C/p>\n\u003Cp>An alternate LED or resistor can change both current and visibility even when it fits the same footprint. Evaluate the exact proposed part through the project&#39;s \u003Ca href=\"/en/blog/pcb-component-substitution-approval/\">component substitution approval\u003C/a> process, including electrical, optical, thermal and assembly requirements.\u003C/p>\n\u003Ch2>Why headroom and the driver matter\u003C/h2>\n\u003Cp>\u003Cstrong>Headroom\u003C/strong> is the voltage left for the resistor after the LED and other series drops. At the fictional nominal point, it is 3.00 V. If the available voltage is only slightly above the LED’s operating voltage, a small change in supply or LED voltage becomes a large fraction of the resistor voltage. Current—and therefore visible output—can vary substantially.\u003C/p>\n\u003Cp>When there is too little voltage to support the assumed forward operating point, the simple subtraction no longer gives a useful positive operating current. The LED may conduct only weakly or not provide useful indication. Do not treat a negative calculated current as a real reverse current.\u003C/p>\n\u003Cp>If low headroom or supply variation makes the required visibility and current limits incompatible, reassess the source, LED, and topology. A suitably specified constant-current approach may be worth evaluating, but it also needs sufficient operating voltage and its own thermal and electrical checks.\u003C/p>\n\u003Ch3>When a GPIO drives the LED\u003C/h3>\n\u003Cp>A microcontroller GPIO is not necessarily an ideal supply or return. Depending on whether it sources or sinks current, use its applicable \u003Cstrong>loaded output voltage\u003C/strong> rather than assuming the pin is exactly at the supply or ground rail. Do not subtract a separate driver drop if it is already accounted for in the voltage used across the LED and resistor.\u003C/p>\n\u003Cp>Check the exact controller’s:\u003C/p>\n\u003Cul>\n\u003Cli>Per-pin source or sink current limits and output-voltage specifications.\u003C/li>\n\u003Cli>Aggregate port and device current limits.\u003C/li>\n\u003Cli>Behavior during reset, startup, and power-off.\u003C/li>\n\u003Cli>Allowed pin voltage relative to its supply rails.\u003C/li>\n\u003C/ul>\n\u003Cp>Then verify that the resulting current supports the indicator requirement without exceeding the LED, GPIO, or resistor limits.\u003C/p>\n\u003Ch2>Verify the assembled indicator\u003C/h2>\n\u003Cp>Define the test supply, operating temperature, drive state, measurement points and visibility criteria before checking the assembly. With appropriate equipment and access, measure the loaded voltage across the resistor and estimate current using \u003Ccode>I = VR / R\u003C/code> and an appropriate resistance value. If measuring resistance, remove power and isolate the resistor as needed to avoid other circuit paths; account for resistance changes between that measurement and operation. Alternatively, measure current directly with a suitable instrument in series; account for the instrument&#39;s voltage drop because it can alter a low-headroom circuit.\u003C/p>\n\u003Cp>Compare observations at relevant supply and temperature conditions with the project&#39;s current and visibility requirements. Record the LED and resistor part numbers, board revision, measurement conditions and results. A few passing assemblies provide useful observations but do not establish a guaranteed production range; choose sample coverage and acceptance criteria for the actual project. An \u003Ca href=\"/en/blog/pcb-assembly-inspection-report/\">assembly inspection report\u003C/a> can record the agreed checks, results and exceptions without implying that inspection alone validates the circuit design.\u003C/p>\n\u003Ch2>Decision table\u003C/h2>\n\u003Ctable>\n\u003Cthead>\n\u003Ctr>\n\u003Cth>Design observation\u003C/th>\n\u003Cth>Starting decision\u003C/th>\n\u003Cth>Further evidence needed\u003C/th>\n\u003C/tr>\n\u003C/thead>\n\u003Ctbody>\u003Ctr>\n\u003Ctd>Nominal calculation produces a value between available resistors\u003C/td>\n\u003Ctd>Compare adjacent available values, often starting with the higher one\u003C/td>\n\u003Ctd>Current and visibility at both supply extremes\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Minimum LED voltage is not guaranteed\u003C/td>\n\u003Ctd>Do not label a calculated maximum current as guaranteed\u003C/td>\n\u003Ctd>Supplier boundary, characterization, or documented assumption and margin\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Supply is only slightly above LED voltage\u003C/td>\n\u003Ctd>Treat the resistor approach as sensitive to variation\u003C/td>\n\u003Ctd>Loaded voltages, LED behavior, visibility, and possible alternative drive\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>GPIO output supplies or sinks the current\u003C/td>\n\u003Ctd>Include its loaded voltage in the loop\u003C/td>\n\u003Ctd>Pin and aggregate limits, reset behavior, and rail conditions\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Calculated resistor power appears small\u003C/td>\n\u003Ctd>Compare it with the exact part’s allowable dissipation\u003C/td>\n\u003Ctd>Temperature, board thermal path, derating, and stability\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Indicator works on one prototype\u003C/td>\n\u003Ctd>Treat it as an observation, not release proof\u003C/td>\n\u003Ctd>Representative current, visibility, and temperature checks\u003C/td>\n\u003C/tr>\n\u003C/tbody>\u003C/table>\n\u003Ch2>A resistor is not a protection system\u003C/h2>\n\u003Cp>A series resistor limits current in the intended LED loop under the conditions for which it was designed. It is not automatically a fuse, an ESD protection device, or protection against every short, transient, reverse voltage, or component fault.\u003C/p>\n\u003Cp>For example, a fault can change which components carry current and how much power the resistor dissipates. ESD protection may require a separately designed path and components with appropriate ratings. Evaluate relevant faults and protection requirements independently rather than assuming the indicator resistor makes the circuit safe.\u003C/p>\n\u003Cp>For background on how resistors and LEDs fit into a broader assembly, see \u003Ca href=\"/en/blog/circuit-board-components/\">circuit board components\u003C/a>.\u003C/p>\n\u003Ch2>Practical review checklist\u003C/h2>\n\u003Cp>Before releasing the design, record:\u003C/p>\n\u003Cul>\n\u003Cli>The exact LED and resistor part numbers and the datasheet revisions used.\u003C/li>\n\u003Cli>Supply minimum and maximum, including the voltage actually available to the indicator circuit.\u003C/li>\n\u003Cli>Required visibility, operating temperature, duty, and service conditions.\u003C/li>\n\u003Cli>The LED current and voltage evidence at relevant operating points, including any missing guarantees.\u003C/li>\n\u003Cli>Nominal resistance, selected standard value, tolerance, and expected resistance changes.\u003C/li>\n\u003Cli>High-current and low-current calculations with their assumptions clearly identified.\u003C/li>\n\u003Cli>Resistor worst-case dissipation and the exact part’s thermal and stability limits.\u003C/li>\n\u003Cli>LED and driver current limits, including temperature derating and GPIO constraints where applicable.\u003C/li>\n\u003Cli>Results from representative assemblies, including current and visibility—not merely whether the LED lights.\u003C/li>\n\u003Cli>Separate consideration of faults, reverse voltage, transients, and ESD where relevant.\u003C/li>\n\u003C/ul>\n\u003Cp>Nominal math helps choose a starting resistor. It is \u003Cstrong>not worst-case validation\u003C/strong>, and a calculated range based on unverified assumptions is not a guaranteed production range.\u003C/p>\n\u003Cp>For \u003Ca href=\"/en/products/pcb-assembly/\">PCB assembly\u003C/a>, provide the LED and resistor MPNs, polarity information, BOM, board files and any required inspection or powered-test criteria when you \u003Ca href=\"/en/quote/\">request a quote\u003C/a>. Confirm the build and test scope for the order; design validation remains subject to the project&#39;s requirements.\u003C/p>\n\u003Cdiv data-component=\"BlogQuickQuoteInline\">\u003C/div>\n\n\u003C!-- faq:start -->\n\n\u003Ch2>FAQ\u003C/h2>\n\u003Ch3>Can I use the LED’s typical forward voltage to calculate a resistor?\u003C/h3>\n\u003Cp>Yes, for an initial nominal estimate at an applicable current and temperature. Do not treat the typical value as a guaranteed minimum or maximum when checking production extremes.\u003C/p>\n\u003Ch3>Should I always choose the next higher resistor value?\u003C/h3>\n\u003Cp>Not always. A higher value generally lowers current, but it can also reduce visibility. Compare available values against both the upper current limit and the minimum useful indication.\u003C/p>\n\u003Ch3>Is a resistor’s nominal power calculation enough to select it?\u003C/h3>\n\u003Cp>No. Calculate dissipation at relevant extremes, then check the exact resistor’s rating and derating under the actual thermal and mounting conditions.\u003C/p>\n\u003Ch3>Why can two indicators with the same resistor have different brightness?\u003C/h3>\n\u003Cp>LED voltage and light output vary between devices and with current and temperature. Supply and resistor variation also change current. A visible glow alone does not establish consistent brightness.\u003C/p>\n\u003Ch3>What if the LED datasheet gives no forward-voltage minimum?\u003C/h3>\n\u003Cp>Do not invent one or convert a typical value into a guarantee. Obtain a suitable supplier boundary if possible, or use characterization and a documented engineering assumption while stating the remaining uncertainty.\u003C/p>\n\u003C!-- faq:end -->\n\u003Csection class=\"related-links\" aria-label=\"Related\">\u003Ch3>Related links\u003C/h3>\u003Cul>\u003Cli>\u003Ca href=\"/en/blog/ohms-law/\">Ohm’s Law: Equations, Circuit Examples and PCB Power Loss\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/blog/pcb-component-substitution-approval/\">PCB Component Substitution: An Approval Checklist\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/blog/pcb-assembly-inspection-report/\">PCB Assembly Inspection Report Format: Template and Checklist\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/blog/circuit-board-components/\">Circuit Board Components: Common PCB Parts, What They Do and How to Identify Them\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/products/pcb-assembly/\">PCB assembly\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/quote/\">request a quote\u003C/a>\u003C/li>\u003C/ul>\u003C/section>",[15,18,21,24,27],{"question":16,"answer":17,"answerText":17},"Can I use the LED’s typical forward voltage to calculate a resistor?","Yes, for an initial nominal estimate at an applicable current and temperature. Do not treat the typical value as a guaranteed minimum or maximum when checking production extremes.",{"question":19,"answer":20,"answerText":20},"Should I always choose the next higher resistor value?","Not always. A higher value generally lowers current, but it can also reduce visibility. Compare available values against both the upper current limit and the minimum useful indication.",{"question":22,"answer":23,"answerText":23},"Is a resistor’s nominal power calculation enough to select it?","No. Calculate dissipation at relevant extremes, then check the exact resistor’s rating and derating under the actual thermal and mounting conditions.",{"question":25,"answer":26,"answerText":26},"Why can two indicators with the same resistor have different brightness?","LED voltage and light output vary between devices and with current and temperature. Supply and resistor variation also change current. A visible glow alone does not establish consistent brightness.",{"question":28,"answer":29,"answerText":29},"What if the LED datasheet gives no forward-voltage minimum?","Do not invent one or convert a typical value into a guarantee. Obtain a suitable supplier boundary if possible, or use characterization and a documented engineering assumption while stating the remaining uncertainty.",[31,32,33],"LED resistor","current limiting","PCB design","led-indicator-series-resistor-calculation","en",[35,37,38,39,40,41],"de","it","cn","fr","ru",{"blog":43,"breadcrumb":52},{"@context":44,"@type":45,"headline":4,"description":5,"image":8,"url":46,"datePublished":6,"dateModified":6,"timeRequired":12,"keywords":47,"articleSection":7,"author":48,"publisher":51},"https://schema.org","BlogPosting","https://hilpcb.com/en/blog/led-indicator-series-resistor-calculation/","LED resistor, current limiting, PCB design",{"@type":49,"name":50},"Organization","HILPCB",{"@type":49,"name":50},{"@context":44,"@type":53,"itemListElement":54},"BreadcrumbList",[55,60,64],{"@type":56,"position":57,"name":58,"item":59},"ListItem",1,"Home","https://hilpcb.com/",{"@type":56,"position":61,"name":62,"item":63},2,"Blog","https://hilpcb.com/en/blog/",{"@type":56,"position":65,"name":34,"item":46},3,1795020490888]