[{"data":1,"prerenderedAt":66},["ShallowReactive",2],{"blog-potentiometer-trimmer-wiring-pcb-release-en":3},{"title":4,"description":5,"date":6,"lastUpdated":6,"category":7,"image":8,"imageAlt":9,"readingTime":10,"wordCount":11,"timeRequired":12,"htmlContent":13,"faq":14,"tags":30,"slug":34,"sourceLocale":35,"availableLocales":36,"jsonld":42},"Potentiometer PCB Wiring and Footprint: Pin Mapping and Assembly","Map a potentiometer or trimmer's exact part drawing to PCB pads and schematic nets, then verify adjustment access, assembly limits and test requirements.","2026-11-11","design","/assets/blogs/potentiometer-trimmer-wiring-pcb-release/trimmer-release-cover.svg","Conceptual trimmer beside a part drawing and PCB footprint review, without a terminal assignment",13,2557,"PT13M","\u003Cp>To place a potentiometer or trimmer on a PCB, map the \u003Cstrong>exact manufacturer part number (MPN)\u003C/strong> from its electrical terminal diagram and mechanical drawing to the schematic nets and numbered footprint pads. Then check adjustment access, ratings and the assembly and test instructions for that specific part.\u003C/p>\n\u003Cp>Two parts with the same resistance can have different physical terminal layouts, adjustment access or rotation behavior. Do not assume a generic rule such as “pin 1 is supply” or that terminals appear in numerical order from left to right.\u003C/p>\n\u003Cp>For broader component context, see \u003Ca href=\"/en/blog/circuit-board-components/\">circuit board components\u003C/a>.\u003C/p>\n\u003Ch2>Define the circuit before mapping the PCB footprint\u003C/h2>\n\u003Cp>A potentiometer has a resistive element with a fixed terminal at each end and a movable contact called the \u003Cstrong>wiper\u003C/strong>. Moving the shaft or adjustment screw changes the resistance between the wiper and each end. A trimmer is generally intended for adjustment with a tool, often during setup or calibration; its exact intended use and durability depend on the part.\u003C/p>\n\u003Cp>In a \u003Cstrong>voltage divider\u003C/strong>, both fixed ends are connected to circuit nodes and the wiper provides an adjustable voltage. For an ideal, unloaded divider connected between a positive reference and ground:\u003C/p>\n\u003Cdiv class=\"math-block\">V\u003Csub>wiper\u003C/sub> = V\u003Csub>reference\u003C/sub> * (R\u003Csub>ground-to-wiper\u003C/sub>)/(R\u003Csub>total\u003C/sub>)\u003C/div>\n\n\u003Cp>This approximation assumes negligible wiper loading. A load draws current, changes the division ratio and can affect power in the element. Use the actual load, tolerance and taper when checking the usable output range.\u003C/p>\n\u003Cp>In a \u003Cstrong>rheostat\u003C/strong>, the wiper and one fixed end form a variable resistance. The third terminal may be left unconnected or, where appropriate for the circuit, connected to the wiper. Tying it to the wiper can reduce the chance of an open circuit if contact is momentarily lost, but it does not guarantee fail-safe operation or remove the need to analyze faults.\u003C/p>\n\u003Cp>A rheostat can approach a very low resistance at one end of travel. Provide whatever independent current limiting the circuit needs; do not rely on the pot’s setting to protect the circuit.\u003C/p>\n\u003Cp>Linking the wiper of a board-mounted potentiometer or trimmer to one end may reduce an open-wiper excursion in some rheostat circuits, but this is not a fail-safe function and does not protect against every wiper, track, solder, connector, setting, overcurrent, or downstream fault. Analyze the actual circuit’s maximum current, voltage, local dissipation, minimum resistance, fault action, and independent current limiting under the selected part’s data-sheet conditions. The adjustment setting must not be treated as a safety or overcurrent device. For release, assess the specific application rather than assuming a wiring arrangement or part rating guarantees protection or approval.\u003C/p>\n\u003Ch3>Wiring decision table\u003C/h3>\n\u003Ctable>\n\u003Cthead>\n\u003Ctr>\n\u003Cth>Design choice\u003C/th>\n\u003Cth>Connection approach\u003C/th>\n\u003Cth>Release check\u003C/th>\n\u003C/tr>\n\u003C/thead>\n\u003Ctbody>\u003Ctr>\n\u003Ctd>Adjustable reference\u003C/td>\n\u003Ctd>Connect both fixed ends to reference nets; take the output from the wiper\u003C/td>\n\u003Ctd>Confirm load effects, output range and desired rotation direction\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Variable resistance\u003C/td>\n\u003Ctd>Use the wiper and one fixed end\u003C/td>\n\u003Ctd>Check minimum resistance, current limiting and behavior if contact is lost\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Variable resistance with wiper-to-end link\u003C/td>\n\u003Ctd>Connect the unused fixed end to the wiper, if the circuit permits\u003C/td>\n\u003Ctd>Analyze normal and fault behavior; do not treat the link as a safety guarantee\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>User-operated control\u003C/td>\n\u003Ctd>Choose a part intended for the required operation and access\u003C/td>\n\u003Ctd>Check shaft, panel, knob, life and direction from the user’s viewpoint\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Calibration trimmer\u003C/td>\n\u003Ctd>Choose an adjustment style suited to setup and service\u003C/td>\n\u003Ctd>Define tool access, measurement conditions and whether later adjustment is allowed\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Proposed substitute\u003C/td>\n\u003Ctd>Compare the complete part, not just resistance\u003C/td>\n\u003Ctd>Requalify electrical mapping, footprint, mechanical access and process limits\u003C/td>\n\u003C/tr>\n\u003C/tbody>\u003C/table>\n\u003Cp>A potentiometer should not be selected as a direct high-current LED or motor control without circuit-specific rating analysis. In many designs it is better used to provide a low-current control signal to a suitably rated driver.\u003C/p>\n\u003Ch2>Lock the exact part before drawing the footprint\u003C/h2>\n\u003Cp>The release record should identify the manufacturer and \u003Cstrong>full order code\u003C/strong>, including the mechanical model and any relevant suffixes. Record the controlled datasheet revision and confirm at least:\u003C/p>\n\u003Cul>\n\u003Cli>Nominal resistance, tolerance and taper.\u003C/li>\n\u003Cli>Adjustment type, orientation and number of turns.\u003C/li>\n\u003Cli>Package or terminal form, mounting style and packaging.\u003C/li>\n\u003Cli>Electrical ratings and environmental limits.\u003C/li>\n\u003Cli>Applicable ordering and assembly requirements.\u003C/li>\n\u003C/ul>\n\u003Cp>Resistance alone is not enough. A linear taper and a logarithmic taper can produce different output changes at the same shaft position. A top-adjust trimmer and a side-adjust trimmer may need different tool clearance even when they share an electrical symbol.\u003C/p>\n\u003Cp>For example, the Bourns 3386 family datasheet identifies terminal \u003Cstrong>2 as the wiper, 1 as the counterclockwise end and 3 as the clockwise end\u003C/strong> in its circuit convention. That is a family-specific example, not a universal numbering rule. The 3386 also includes mechanical models with different terminal arrangements. Check the current datasheet and the exact model before using those labels in a design.\u003C/p>\n\u003Cp>When releasing a board-mounted potentiometer or trimmer, treat terminal numbering, physical order, adjustment direction, footprint and ratings as properties of the exact manufacturer order code and its drawing, not universal facts about three-terminal potentiometers. Reconcile the current MPN and the model drawing’s stated view with schematic nets and numbered PCB pads. Define the clockwise viewpoint and check adjustment access, assembly, cleaning and coating constraints, and any calibration instruction. Continuity or a familiar package shape does not prove loaded adjustment direction, safe dissipation, calibration or substitution equivalence. Resolve discrepancies using current manufacturer documentation and the applicable calibration procedure.\u003C/p>\n\u003Ch2>Reconcile the drawing view with the board\u003C/h2>\n\u003Cp>A terminal number is an electrical identifier; it is not inherently a left, center or right PCB position. Before assigning pads, determine whether each manufacturer drawing is a top, bottom, front or side view. Note the viewpoint used for rotation as well: “clockwise” needs a defined viewing direction.\u003C/p>\n\u003Cp>Use the model-specific dimensions and drawings to build a mapping like this:\u003C/p>\n\u003Ctable>\n\u003Cthead>\n\u003Ctr>\n\u003Cth>Datasheet evidence\u003C/th>\n\u003Cth>Design record\u003C/th>\n\u003C/tr>\n\u003C/thead>\n\u003Ctbody>\u003Ctr>\n\u003Ctd>Terminal number and electrical function\u003C/td>\n\u003Ctd>Schematic pin number and net name\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Physical terminal location in the stated view\u003C/td>\n\u003Ctd>Footprint pad number and position\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Body and adjustment location\u003C/td>\n\u003Ctd>Board outline, courtyard and access direction\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>Rotation convention\u003C/td>\n\u003Ctd>Expected change at the measured output\u003C/td>\n\u003C/tr>\n\u003C/tbody>\u003C/table>\n\u003Cp>Do not transfer a bottom-view image to a top-view footprint without accounting for the changed viewpoint. Check orientation using dimensions and known features, not a generic illustration or an assumed pin-one marker.\u003C/p>\n\u003Cp>For a \u003Cstrong>hypothetical unloaded divider\u003C/strong> using a 3386-family part, the circuit convention in that family&#39;s datasheet permits the following electrical mapping when the intended output should increase toward the manufacturer&#39;s clockwise end:\u003C/p>\n\u003Ctable>\n\u003Cthead>\n\u003Ctr>\n\u003Cth>3386 circuit terminal\u003C/th>\n\u003Cth>Example schematic net\u003C/th>\n\u003Cth>PCB check\u003C/th>\n\u003C/tr>\n\u003C/thead>\n\u003Ctbody>\u003Ctr>\n\u003Ctd>1, counterclockwise end\u003C/td>\n\u003Ctd>\u003Ccode>GND\u003C/code>\u003C/td>\n\u003Ctd>Position footprint pad 1 for terminal 1 using the selected model&#39;s stated drawing view.\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>2, wiper\u003C/td>\n\u003Ctd>\u003Ccode>ADJUST_OUT\u003C/code>\u003C/td>\n\u003Ctd>Position footprint pad 2 for terminal 2 using the selected model&#39;s stated drawing view.\u003C/td>\n\u003C/tr>\n\u003Ctr>\n\u003Ctd>3, clockwise end\u003C/td>\n\u003Ctd>\u003Ccode>VREF\u003C/code>\u003C/td>\n\u003Ctd>Position footprint pad 3 for terminal 3 using the selected model&#39;s stated drawing view.\u003C/td>\n\u003C/tr>\n\u003C/tbody>\u003C/table>\n\u003Cp>This is an electrical example, not a footprint or a mapping for another family. \u003Ccode>VREF\u003C/code> is the higher reference in this example. The board&#39;s actual load, the selected order code and drawing view, and the user&#39;s adjustment viewpoint still require verification; numbered pads in the table do not establish their physical positions.\u003C/p>\n\u003Cp>A useful review is to place the schematic symbol, footprint and relevant drawing views side by side. Trace every terminal from the resistive element to its numbered physical lead, then to the corresponding pad and net. A 3D model can help with mechanical review, but it does not replace the terminal drawing.\u003C/p>\n\u003Ch2>Map nets and define direction\u003C/h2>\n\u003Cp>Name the schematic nets according to their actual purpose—for example, \u003Ccode>VREF\u003C/code>, \u003Ccode>GND\u003C/code> and \u003Ccode>ADJUST_OUT\u003C/code>—and state which electrical end and wiper connect to each. The fixed ends can be assigned in either order when the circuit permits. Swapping them reverses the voltage-divider response.\u003C/p>\n\u003Cp>For a divider intended to increase as the wiper moves toward the manufacturer-defined clockwise end, connect the higher reference to that end and the lower reference to the opposite end. Then verify that the definition of clockwise matches the direction the assembler or user will see at the adjustment feature. Do not infer that relationship from a symbol alone.\u003C/p>\n\u003Cp>Write the requirement in observable terms, such as:\u003C/p>\n\u003Cblockquote>\n\u003Cp>Viewed from the adjustment side, clockwise adjustment increases the measured \u003Ccode>ADJUST_OUT\u003C/code> voltage under the specified test conditions.\u003C/p>\n\u003C/blockquote>\n\u003Cp>For a rheostat, describe whether clockwise adjustment should increase or decrease resistance between the named nets. The answer depends on which fixed end is used and on the selected part’s convention.\u003C/p>\n\u003Cp>Also review startup, end-of-travel and wiper-fault behavior. A floating or intermittent wiper can create an unsafe or undefined control signal. A pull resistor, buffer, limiting network or other protection may be appropriate, depending on the circuit.\u003C/p>\n\u003Ch2>Check current, power and voltage\u003C/h2>\n\u003Cp>The resistance value does not by itself establish whether the part can survive the application. Use the exact part documentation and calculate the worst case across the full adjustment range.\u003C/p>\n\u003Cp>Check:\u003C/p>\n\u003Cul>\n\u003Cli>\u003Cstrong>Total element power\u003C/strong>, including ambient-temperature derating and applicable operating conditions.\u003C/li>\n\u003Cli>\u003Cstrong>Wiper current\u003C/strong> and any separate contact-current limit.\u003C/li>\n\u003Cli>\u003Cstrong>Local dissipation\u003C/strong> in the active portion of the element, particularly in rheostat use.\u003C/li>\n\u003Cli>\u003Cstrong>Maximum working voltage\u003C/strong>, terminal-to-terminal conditions and expected transients.\u003C/li>\n\u003Cli>Tolerance, end resistance, load current and possible short or open faults.\u003C/li>\n\u003C/ul>\n\u003Cp>For a loaded divider, calculate currents and dissipation with the load connected; the unloaded divider equation is not a complete rating check. For a rheostat, do not assume the full-element power rating applies to a small section of track near an end stop. Use the manufacturer’s limits and application guidance.\u003C/p>\n\u003Cp>The design must remain within ratings at the worst setting, supply, load and temperature—not just at the calibration point.\u003C/p>\n\u003Cdiv data-component=\"BlogQuickQuoteInline\">\u003C/div>\n\n\u003Ch2>Release the footprint and mechanical access\u003C/h2>\n\u003Cp>The footprint must match the exact mechanical model, not merely the family name. Check pad and hole sizes, terminal spacing, body outline and courtyard against the controlled drawing. Account for manufacturing tolerances and applicable PCB design rules.\u003C/p>\n\u003Cp>Then review the assembled product:\u003C/p>\n\u003Cul>\n\u003Cli>Can the specified tool reach the screw without striking nearby components or an enclosure?\u003C/li>\n\u003Cli>For a shaft control, do the panel opening, shaft length, bushing, knob and board location align?\u003C/li>\n\u003Cli>Is mechanical retention adequate for insertion, adjustment and expected use?\u003C/li>\n\u003Cli>Can the body and solder joints be inspected after assembly?\u003C/li>\n\u003Cli>Is there enough clearance for the adjustment arc or screwdriver approach?\u003C/li>\n\u003Cli>Are board-to-panel tolerances and any required assembly sequence documented?\u003C/li>\n\u003C/ul>\n\u003Cp>Do not assume a top-adjust component remains accessible once the board is enclosed. Likewise, a side-adjust part may need clearance beyond the PCB edge or through a case opening.\u003C/p>\n\u003Cp>Review the component’s soldering, cleaning and handling limits against the intended assembly process. Document cleaning and coating keepouts around the adjustment feature and other sensitive areas as required by the part and process. Avoid assuming that coating is allowed inside the mechanism or that visual cleanliness proves the mechanism is unaffected.\u003C/p>\n\u003Ch2>Define calibration and test before release\u003C/h2>\n\u003Cp>An assembly drawing should tell the operator \u003Cstrong>what to adjust, what to measure and what result is acceptable\u003C/strong>. A complete instruction identifies:\u003C/p>\n\u003Col>\n\u003Cli>The board revision, component reference and accessible adjustment feature.\u003C/li>\n\u003Cli>Power, load, warm-up and environmental conditions.\u003C/li>\n\u003Cli>Measurement nodes, instrument requirements and target range.\u003C/li>\n\u003Cli>Adjustment direction and a safe starting condition.\u003C/li>\n\u003Cli>Limits on travel, retest steps and the response if the target cannot be reached.\u003C/li>\n\u003Cli>Whether sealing, tamper control or field adjustment is permitted.\u003C/li>\n\u003C/ol>\n\u003Cp>Follow the component’s guidance for end stops and adjustment force. Do not assume that every multiturn device has the same stop or clutch behavior.\u003C/p>\n\u003Cp>On a prototype, first verify the physical and electrical mapping with power removed and the circuit safely isolated as appropriate. In-circuit resistance readings may be influenced by parallel paths, so interpret them accordingly. Then, under controlled operating conditions, sweep the usable range and verify the measured response, direction and calibration range.\u003C/p>\n\u003Cp>A continuity check or visual orientation check is useful but insufficient: neither proves that the loaded circuit behaves correctly throughout adjustment or meets its calibrated target.\u003C/p>\n\u003Cp>When documenting the results, an \u003Ca href=\"/en/blog/pcb-assembly-inspection-report/\">assembly inspection report\u003C/a> can help connect the board revision, checks, measurements and any exceptions to the relevant records.\u003C/p>\n\u003Ch2>Assembly release and substitutions\u003C/h2>\n\u003Cp>Give the assembler a consistent set of documents: BOM, placement data, footprint, assembly drawing, process notes and test instructions. Identify the exact component and any orientation features that are actually present on it. Resolve discrepancies between documents before building.\u003C/p>\n\u003Cp>Treat a proposed substitute as a new comparison, even if its resistance and body appearance match. Review its terminal functions and physical views, taper, ratings, travel, adjustment direction, soldering limits, access and calibration behavior. Update the controlled records and prototype checks where needed; do not quietly exchange MPNs on resistance alone.\u003C/p>\n\u003Cp>For a \u003Ca href=\"/en/products/pcb-assembly/\">PCB assembly\u003C/a> project discussion, you can \u003Ca href=\"/en/quote/\">request a quote\u003C/a> with the BOM, drawings, adjustment access and test requirements. Confirm the agreed scope rather than assuming that sourcing, calibration or a particular assembly process is included.\u003C/p>\n\u003Ch3>Release checklist\u003C/h3>\n\u003Cul>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Full manufacturer order code and current datasheet revision are recorded.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Drawing views and physical terminal locations are reconciled with numbered footprint pads.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Each electrical terminal is mapped to a named schematic net.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Clockwise and counterclockwise behavior is specified from a defined viewpoint.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Resistance, taper, tolerance, voltage, current and power are checked across the operating range.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Wiper faults, end positions and current limiting are addressed.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Footprint, courtyard, tool access and panel interfaces are reviewed.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Soldering, cleaning, coating keepouts and inspection requirements are documented.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Calibration conditions, acceptance limits and adjustment permissions are defined.\u003C/li>\n\u003Cli>\u003Cinput disabled=\"\" type=\"checkbox\"> Prototype behavior is verified, and substitutions require renewed review.\u003C/li>\n\u003C/ul>\n\u003C!-- faq:start -->\n\n\u003Ch3>Is the middle terminal always the wiper?\u003C/h3>\n\u003Cp>No. Some families identify terminal 2 as the wiper, but numbering and physical placement are not universal. Use the circuit diagram and mechanical drawing for the exact MPN.\u003C/p>\n\u003Ch3>How do I reverse the direction of a voltage-divider control?\u003C/h3>\n\u003Cp>Where the circuit allows it, swap the two fixed-end connections. Verify the result on the selected part from the specified viewing direction and with the intended load connected.\u003C/p>\n\u003Ch3>Should I connect the unused rheostat terminal to the wiper?\u003C/h3>\n\u003Cp>It can be useful in some circuits because it may reduce the chance of an open circuit if wiper contact is interrupted. Confirm that the connection is appropriate for the circuit and analyze faults; it is not a fail-safe guarantee.\u003C/p>\n\u003Ch3>How do I verify the assembled trimmer&#39;s adjustment direction?\u003C/h3>\n\u003Cp>First check the physical and electrical mapping with power removed and the circuit safely isolated as appropriate. Then, under defined supply and load conditions, measure the intended output while adjusting from the stated viewpoint. A visual or continuity check alone does not prove the loaded response.\u003C/p>\n\u003Ch3>Can I substitute a trimmer with the same resistance?\u003C/h3>\n\u003Cp>Not without review. Check its complete order code, terminal mapping, mechanical model, taper, ratings, adjustment access, process limits and calibration behavior against the released design.\u003C/p>\n\u003C!-- faq:end -->\n\u003Csection class=\"related-links\" aria-label=\"Related\">\u003Ch3>Related links\u003C/h3>\u003Cul>\u003Cli>\u003Ca href=\"/en/blog/circuit-board-components/\">Circuit Board Components: Common PCB Parts, What They Do and How to Identify Them\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/blog/pcb-assembly-inspection-report/\">PCB Assembly Inspection Report Format: Template and Checklist\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/products/pcb-assembly/\">PCB assembly\u003C/a>\u003C/li>\u003Cli>\u003Ca href=\"/en/quote/\">request a quote\u003C/a>\u003C/li>\u003C/ul>\u003C/section>",[15,18,21,24,27],{"question":16,"answer":17,"answerText":17},"Is the middle terminal always the wiper?","No. Some families identify terminal 2 as the wiper, but numbering and physical placement are not universal. Use the circuit diagram and mechanical drawing for the exact MPN.",{"question":19,"answer":20,"answerText":20},"How do I reverse the direction of a voltage-divider control?","Where the circuit allows it, swap the two fixed-end connections. Verify the result on the selected part from the specified viewing direction and with the intended load connected.",{"question":22,"answer":23,"answerText":23},"Should I connect the unused rheostat terminal to the wiper?","It can be useful in some circuits because it may reduce the chance of an open circuit if wiper contact is interrupted. Confirm that the connection is appropriate for the circuit and analyze faults; it is not a fail-safe guarantee.",{"question":25,"answer":26,"answerText":26},"How do I verify the assembled trimmer's adjustment direction?","First check the physical and electrical mapping with power removed and the circuit safely isolated as appropriate. Then, under defined supply and load conditions, measure the intended output while adjusting from the stated viewpoint. A visual or continuity check alone does not prove the loaded response.",{"question":28,"answer":29,"answerText":29},"Can I substitute a trimmer with the same resistance?","Not without review. Check its complete order code, terminal mapping, mechanical model, taper, ratings, adjustment access, process limits and calibration behavior against the released design.",[31,32,33],"potentiometer PCB footprint","trimmer wiring","PCB design","potentiometer-trimmer-wiring-pcb-release","en",[35,37,38,39,40,41],"de","it","cn","fr","ru",{"blog":43,"breadcrumb":52},{"@context":44,"@type":45,"headline":4,"description":5,"image":8,"url":46,"datePublished":6,"dateModified":6,"timeRequired":12,"keywords":47,"articleSection":7,"author":48,"publisher":51},"https://schema.org","BlogPosting","https://hilpcb.com/en/blog/potentiometer-trimmer-wiring-pcb-release/","potentiometer PCB footprint, trimmer wiring, PCB design",{"@type":49,"name":50},"Organization","HILPCB",{"@type":49,"name":50},{"@context":44,"@type":53,"itemListElement":54},"BreadcrumbList",[55,60,64],{"@type":56,"position":57,"name":58,"item":59},"ListItem",1,"Home","https://hilpcb.com/",{"@type":56,"position":61,"name":62,"item":63},2,"Blog","https://hilpcb.com/en/blog/",{"@type":56,"position":65,"name":34,"item":46},3,1795020492165]