Embedded Components in PCBs: Planar Resistors, Capacitance and Limits

Compare formed and placed embedded components, explore idealized resistor and capacitance calculations, and identify design and supplier questions.

Embedded components are built into or placed within a PCB’s layer structure rather than mounted on its outer surface. Formed components use materials and features of the board, such as patterned resistive film or a dielectric between conductive planes. Placed components are discrete parts or dies incorporated into the stackup.

Both approaches can be worth considering when surface area, routing, or power-distribution connections are important. Neither is an automatic improvement: the geometry, materials, supplier process, power requirements, test access, and rework approach need to be agreed for the actual design.

The calculations below are idealized examples, not measured performance, supplier commitments, or qualification evidence.

Formed and placed options

Option How it can be implemented Questions for the design and supplier
Formed planar resistor Pattern resistive material between conductive terminations What sheet resistance, geometry, tolerance, temperature behavior, power handling, and test process can be supported?
Formed capacitance Use a dielectric between conductive planes as part of the power-distribution structure What are the effective plane area, dielectric properties, connections, and behavior across the required frequency range?
Placed component or die Incorporate a discrete part or die within the board structure What placement, connection, cavity or core geometry, thermal, inspection, test, and rework approach is suitable for that part?

Possible applications include termination and bias networks, power distribution, and designs with limited surface space. Whether a particular component is suitable depends on its electrical and mechanical requirements and on the agreed manufacturing process. Compare an embedded approach with a surface-mounted alternative, especially when values may change during development or test access is important.

Sizing a planar resistor

For an idealized rectangular resistor, resistance is sheet resistance multiplied by the number of squares. This relationship and the 25 Ω/sq, two-square example are described in the OhmegaPly Design Guide v2.1; the model does not itself establish manufacturing tolerance:

R = Rs × (L / W)

Here, Rs is sheet resistance in ohms per square, L is the resistive length between terminations, and W is the width. For example, an ideal rectangle with Rs = 25 Ω/sq, L = 0.50 mm, and W = 0.25 mm has two squares and a nominal resistance of 50 Ω.

An idealized bound calculation

Assume the following independent bounds:

  • Nominal L = 0.50 mm and W = 0.25 mm, each bounded by ±0.0125 mm.
  • Sheet resistance bounded by ±5% of nominal.
  • The extreme values of all three inputs can occur simultaneously.
  • The ideal rectangular model applies, without additional termination or process effects.

Relative to nominal resistance, the extreme ratios are:

Case Calculation Ratio to nominal Change
High 1.05 × (0.5125/0.2375)/2 1.1329 +13.29%
Low 0.95 × (0.4875/0.2625)/2 0.8821 −11.79%

These are the model’s extreme ratios, rounded to four decimal places, conditional on the assumed bounds being simultaneously possible. They are not a production tolerance. Obtain actual process bounds and correlations from the fabricator, and agree how trimming, measurement stages, and acceptance limits will be handled. Terminations, material behavior, temperature, and later processing may also affect a real resistor.

Power and temperature

Assess resistor power using the actual circuit, geometry, material data, surrounding stackup, and operating temperature. Ask the supplier how the proposed structure is evaluated and what evidence supports its rating. There is no universal power threshold that determines whether an embedded resistor is suitable.

Temperature-dependent resistance and the required circuit accuracy also matter. A bias resistor, termination, or precision network should be evaluated against its own allowable variation rather than assigned a generic embedded-resistor tolerance.

What embedded capacitance estimates—and what it does not

An ideal parallel-plate estimate is:

C = (ε0 εr A / d)

Here, ε0 is the permittivity of free space, εr is the assumed relative permittivity, A is effective overlapping area, and d is dielectric thickness.

For an illustrative calculation, assume two ideal plates overlap across a full 100 mm × 80 mm area, or 0.008 m2. With d = 24 μm = 24 × 10-6 m, εr = 4.4 at the frequency of interest, and ε0 = 8.854 × 10-12 F/m:

C ≈ ((8.854 × 10-12 F/m)(4.4)(0.008 m2) / 24 × 10-6 m) ≈ 13 nF

This assumes full overlap of two distinct conductors separated by a uniform dielectric in an ideal quasi-static model and ignores edge effects, cutouts, and losses. Actual effective area may be smaller, and material properties can vary with frequency. Depending on geometry and frequency, distributed plane behavior and resonances may matter. The result is neither a measured capacitance nor a predicted impedance or qualification result.

A complete power distribution network (PDN) also includes the source and loads, the planes’ geometry and resonances, connections and vias, package and die connections, package capacitance, and, where present, discrete capacitors and their mounting parasitics. Plane capacitance and discrete components, where present, may interact across frequency, including through resonances, and the effectiveness of discrete capacitors depends on frequency and the rest of the network. Discrete capacitors do not stop contributing above a universal frequency, and connections to the die do not have negligible inductance by assumption.

Model and, where appropriate, measure the complete PDN against the design’s impedance targets. Do not infer that a plane pair replaces a particular discrete capacitor from capacitance alone.

Layout and stackup decisions

Agree layout details with the fabricator for the selected materials and process. The following are design questions, not universal manufacturing rules:

Decision What to review
Resistor geometry and terminations Required value, dimensional variation, material behavior, registration, and termination effects
Layer placement and routing Access to the served nets, connection parasitics, and test access
Clearances and holes The proposed geometry and any process-specific restrictions near resistive material or embedded parts
Capacitance planes Effective overlap, plane interruptions, dielectric properties, connection paths, and PDN resonances
Stackup mechanics Layer balance, materials, lamination sequence, and mechanical requirements
Placed components Part dimensions, cavity or core design, connections, thermal behavior, inspection, and test

For stackups that use sequential lamination, the buried via guide provides related context.

Testing, trimming, and rework

Define the test and acceptance plan before finalizing the design. Depending on the structure and access available, the plan may address:

  • Resistor measurement: Where values can be measured before and after lamination, how parallel circuit paths affect readings, and what limits apply at each stage.
  • Trimming: Whether the proposed process permits trimming, when it would occur, and how subsequent processing is accounted for.
  • Plane integrity: Whether insulation-resistance, dielectric, capacitance, or other tests are appropriate, including agreed test conditions that do not damage the design.
  • Coupons and inspection: Whether coupons or other inspection methods represent the production structure closely enough for the intended acceptance decision.
  • Placed parts: How placement, connections, electrical function, and any thermal requirements will be inspected or tested.
  • Rework: What repair, replacement, bypass, or board-level disposition is feasible and acceptable for the specific construction.

Do not assume that an embedded feature can—or cannot—be reworked. Establish the approach with the supplier and customer for the actual design, including any impact on reliability and acceptance.

RFQ checklist

Confirm applicable project requirements and controlled documents with the customer and fabricator.

For a design review or request for quotation, provide or agree:

  1. Stackup and materials: Proposed layers, geometry, material properties, and any acceptable alternatives.
  2. Component details: Values, tolerances, locations, dimensions, temperature requirements, and power or thermal conditions.
  3. Placed-part details: Part identification, construction, connection approach, and inspection needs.
  4. Tolerance and acceptance: Process bounds, correlations, trimming assumptions, measurement stages, and acceptance limits.
  5. Electrical validation: PDN targets and models where relevant, along with test access and measurement conditions.
  6. Manufacturing and lifecycle: Material and process availability, yield assumptions, rework or disposition approach, and any surface-mount fallback.

For related board categories, see HDI PCBs and multilayer PCBs. The design and test information can also be included in a quote request; confirm material availability and process suitability for the actual design.

FAQ

What are embedded components in a PCB?

They are components formed from board materials or placed within the PCB structure instead of mounted on the outer surface. Examples include patterned resistive films, plane-pair capacitance, and placed discrete parts or dies. Their geometry, materials, connections, and manufacturing process depend on the design.

How accurate are embedded resistors?

Accuracy depends on the material, geometry, process, temperature, trimming, and acceptance method. The idealized example in this article shows +13.29% and −11.79% extremes for its stated simultaneous bounds; it is not a general production tolerance. Obtain actual bounds and correlations from the fabricator.

How do you calculate an embedded resistor’s size?

For an ideal rectangular resistor, use R = Rs × L/W. A 25 Ω/sq material with a 0.50 mm length and 0.25 mm width gives an ideal nominal 50 Ω. Confirm the actual geometry, termination effects, power handling, and tolerance with the supplier.

Can embedded capacitance replace discrete decoupling capacitors?

That depends on the complete PDN and its targets. A parallel-plate calculation estimates capacitance under stated assumptions, but it does not predict the full impedance response. Include planes, connections, package and die parasitics, discrete components, resonances, effective area, and frequency-dependent material properties in the evaluation.

Can embedded components be reworked?

There is no universal answer. Feasibility depends on the component, construction, access, supplier process, and acceptance requirements. Agree on testing, any repair or replacement approach, and board-level disposition for the actual design.