Start with the required turn-off behavior. If a circuit must turn a device off by commanding its gate, an ordinary silicon-controlled rectifier (SCR) is generally the wrong assumption: once latched, it normally remains conducting after gate drive is removed. The circuit must instead reduce anode current and allow the SCR to recover its forward-blocking capability.
For PCB designers and component-identification reviewers, the practical decision is not just whether a gate signal can start conduction. It is whether the actual load, current waveform, temperature, gate circuit, and commutation method support the entire sequence: trigger, latch, conduct, turn off, and recover.
Identify the three terminals first
An ordinary SCR has three terminals:
- Anode (A): The main-current terminal that is positive relative to the cathode during forward-biased operation.
- Cathode (K): The other main-current terminal and the reference for the gate drive.
- Gate (G): The control terminal used to initiate conduction under suitable forward-bias conditions.
In its forward-blocking state, an SCR can have positive anode-to-cathode voltage without carrying normal load current. A suitable gate-to-cathode stimulus initiates regenerative action inside the device, causing it to transition toward conduction. The gate is a trigger input, not an ordinary on/off control.
Do not identify terminal functions from package shape or marking alone. A reviewer needs the complete manufacturer and part identification, including relevant suffixes, and the matching datasheet. Similar-looking devices can have different terminal assignments.
For broader component-identification context, see circuit board components.
Triggering is not the same as latching
Gate trigger current, IGT, describes the gate current needed to trigger an SCR under specified datasheet conditions. It does not, by itself, establish that the load current will rise quickly enough to keep the SCR on after the gate pulse ends.
After triggering begins, the anode current must reach the applicable latching current, IL, while the gate stimulus and current waveform support the transition. If gate drive ends too early, or the load limits current too severely, the SCR may fail to remain on.
That distinction matters with loads whose current rises slowly, including inductive loads. A gate pulse can initiate conduction without providing enough time for anode current to reach the level needed for latching. Gate pulse amplitude, duration, repetition, source impedance, and the load waveform must therefore be considered together.
A datasheet maximum for IGT is not a recommended operating setpoint, a gate absolute-maximum rating, or proof that an arbitrary pulse shape will latch the device. The gate network must be designed against the applicable limits and conditions, including temperature and tolerances.
IL applies initially; IH applies after conduction is established
Once the SCR has latched and is carrying current, holding current, IH, becomes the relevant current criterion for maintaining conduction. If anode current is reduced sufficiently, the SCR can leave the conducting state.
The useful distinction is:
- IL: The initial anode-current requirement associated with remaining on after the triggering gate signal is removed.
- IH: The subsequent anode-current requirement associated with keeping an already conducting SCR on.
IL is commonly higher than IH, but a designer should use the limits and conditions for the exact device rather than assume a universal ratio. Even where a datasheet lists a larger maximum for IL than for IH, those two maximums do not reveal the exact thresholds of an individual SCR.
For these parameters, a specified maximum is a guaranteed upper bound on the respective threshold under the stated test conditions. It is not an absolute maximum rating for current through the anode or gate, an instruction to set current to that number, or the exact switching threshold of every individual device.
One manufacturer example: read the conditions with the numbers
The following example is from the Diodes Incorporated MCR100-8(LS) datasheet, DS45678 Rev. 5-2, October 2023.
For this specific SOT-23 device, the datasheet identifies:
| Pin | Function |
|---|---|
| 1 | Gate |
| 2 | Cathode |
| 3 | Anode |
These assignments apply to the identified part and package. They are not a general SOT-23 pinout or a basis for identifying another manufacturer’s part by appearance.
The electrical-characteristics table uses a default junction temperature of TJ = 25°C unless otherwise noted. The listed test conditions for the following current parameters are VD = 7.0 Vdc and RL = 100 ohm.
| Parameter | Datasheet maximum at 25°C | Datasheet maximum at -40°C |
|---|---|---|
IGT |
50 microamperes | Not stated here |
IH |
5 mA | 10 mA |
IL |
10 mA | 15 mA |
These are specified maximums under the stated conditions, not target current settings or universal SCR values. The colder-temperature limits also show why a single room-temperature number is not enough for a design that must operate across temperature.
In particular, IH = 5 mA maximum at 25°C does not prove that an individual device will turn off when its current reaches 5 mA. Its actual holding behavior can differ, and the circuit waveform and recovery conditions matter.
Threshold and test-condition decision table
Use this table to decide what each item can—and cannot—tell you.
| Design question | Parameter or condition to check | Decision boundary |
|---|---|---|
| Can the gate initiate conduction? | IGT, gate-drive conditions, temperature | Check the available stimulus across supply, source impedance, temperature and tolerances; also respect gate current, power, voltage, pulse-width and duty-cycle ratings. IGT alone does not establish successful latching. |
| Will conduction continue after the gate pulse? | IL, anode-current rise, gate-pulse timing | Check that the load and gate waveform support latching. A maximum IL is not the exact threshold of every device. |
| Can an already conducting SCR remain on? | IH, actual anode current, temperature | IH concerns the established on-state. A maximum IH is not proof of individual turn-off at that number. |
| Can the SCR regain forward blocking? | Current interruption, recovery interval, reapplied voltage, tq if specified | Reducing current is necessary, but the device also needs recovery under applicable conditions. Do not infer tq from IH. |
| Could voltage cause unintended triggering? | Static dv/dt and its test conditions | This concerns sensitivity to a rising forward voltage in the blocking state. It is not a turn-off-time specification. |
| Could current rise damage the device? | On-state di/dt and its test conditions | This concerns the rate of anode-current rise during turn-on. It is not the same as static dv/dt or tq. |
The MCR100-8(LS) datasheet does not specify circuit-commutated turn-off time, tq. It cannot be derived from IH, and the listed dv/dt characteristic cannot substitute for it. If the design requires a quantified recovery interval, obtain appropriate manufacturer information or select a device with the necessary specification.
A hypothetical current comparison
Consider a hypothetical, low-voltage, non-mains circuit at 25°C. Its gate pulse ends when anode current is 12 mA. Later, the load current falls to 3 mA.
Numerically, 12 mA is above the example datasheet’s 10 mA maximum IL, and 3 mA is below its 5 mA maximum IH. But those comparisons alone do not establish the device’s state:
- The hypothetical circuit is not necessarily operating with the datasheet’s VD = 7.0 Vdc and RL = 100 ohm test conditions, or with the same current and gate waveforms. The IL maximum applies to the manufacturer's test conditions; the table does not give a complete gate-removal timing sequence. The 12 mA comparison is not, by itself, proof of latching with an arbitrary load waveform.
- The 3 mA comparison is not proof of turn-off. A particular device’s holding requirement may be lower than the specified maximum, so it may continue conducting at that current. Its prior state and the waveform also matter.
The example illustrates why maximum values are useful for qualified design comparisons but should not be treated as exact individual switching thresholds.
Turn-off requires current reduction and recovery
For an ordinary SCR, removing gate drive after latching normally does not turn it off. The main circuit must reduce anode current below the device’s applicable holding requirement, and the device must have sufficient time and appropriate conditions to recover before forward voltage is reapplied.
The load is central to this decision. A current waveform is not necessarily the same shape or phase as the applied voltage waveform. Stored energy, inductance, capacitance, and other current paths can change when current actually falls and what voltage appears across the SCR afterward.
AC: examine current zero, not just voltage zero
In an AC circuit, natural commutation may occur as the actual SCR current falls toward zero. However, a voltage zero crossing alone does not prove that anode current has stopped or that the SCR has recovered.
A successful turn-off also depends on the time and voltage conditions following current extinction, including the forward voltage subsequently reapplied. A retained gate signal, unintended gate stimulus, or excessive voltage rate of rise can lead to another turn-on. Evaluate the actual load and device conditions rather than assuming every AC half-cycle guarantees recovery.
DC: provide a commutation method
With a DC source, load current may have no natural periodic zero. Turn-off may therefore require a circuit arrangement that interrupts or diverts current, applies suitable reverse bias, or otherwise forces commutation.
The required arrangement depends on the source, load energy, current paths, and recovery conditions. Simply removing the gate signal is not a DC commutation strategy. This is an architectural decision for the circuit designer, not something an assembly reviewer can infer from the presence of an SCR footprint.
Do not confuse SCR recovery with other specifications
GTO is a different device class. A gate-turn-off thyristor is designed for gate-controlled turn-off under its specified conditions. That capability must not be transferred to an ordinary SCR merely because both devices have a gate.
Static dv/dt describes a blocking-state concern: a sufficiently rapid rise in forward voltage can cause unwanted turn-on. Its rating depends on the manufacturer’s test conditions. It does not state how long the device needs to recover after conducting.
On-state di/dt concerns the rate at which anode current rises during turn-on. Excessive rise can concentrate current before conduction spreads adequately through the device. It is a turn-on stress consideration, not a recovery-time measurement.
Circuit-commutated tq is a recovery-time parameter defined under specified test conditions. It relates the end of conduction to the device’s ability to withstand reapplied forward voltage without turning on again. Relevant conditions can include the preceding current, temperature, recovery waveform, and reapplied voltage behavior. A tq value, when available, must be used with those conditions—not as an unconditional delay for every circuit.
Designer and assembly-review responsibilities
The designer owns the electrical decision: selecting the device, defining gate drive, checking latching and holding behavior over the required conditions, establishing the commutation approach, and resolving the recovery-time evidence needed for the application. The designer also accounts for thermal behavior, transients, PCB spacing, and relevant system requirements.
The assembly and component-identification reviewer checks that the released documentation consistently identifies the intended component and orientation. That includes comparing the approved manufacturer part number, suffix, package, symbol, footprint, and placement documentation against the applicable datasheet.
A matching package or a plausible top marking is not enough to approve a substitution. A substitute requires the responsible design authority to assess pinout and electrical behavior, not just physical fit.
PCB release checklist
Before releasing a design or assembly package, confirm that:
- The schematic identifies the complete manufacturer and part number.
- Gate, cathode, and anode agree across the datasheet, symbol, footprint, and placement documentation.
- Gate-drive analysis covers the specified IGT conditions and the required pulse behavior.
- The load-current rise supports latching when gate drive ends.
- IL and IH are checked at relevant temperatures without treating maximums as exact device thresholds.
- The circuit has an explicit turn-off and commutation strategy for the actual load.
- Recovery and reapplied-voltage conditions are addressed; any missing tq information is resolved rather than assumed.
- Static dv/dt and on-state di/dt are reviewed as separate concerns.
- Thermal, transient, spacing, and system requirements are handled by the responsible designer.
- Any proposed substitution receives a complete pinout and electrical review.
For a PCB manufacturing or PCB assembly (PCBA) discussion, include the released design files, BOM with the complete SCR part number, assembly drawing, placement data, quantity, and component sourcing requirements in your quote request. Identify the required inspection and test scope so it can be agreed for the build; the circuit designer remains responsible for the SCR drive and turn-off design.
FAQ
Does removing gate current turn off an ordinary SCR?
Normally, no. After the SCR has latched, its gate is no longer an ordinary off control. The main current must be reduced and the device allowed to recover.
What is the difference between IL and IH?
IL concerns the initial current needed to remain on after the trigger signal is removed. IH concerns maintaining conduction after the SCR is already on. Their specified limits and test conditions depend on the device.
Does an IH maximum mean every SCR turns off at that current?
No. A maximum is a specified limit under stated conditions, not an individual device’s exact switching threshold. Current waveform and recovery conditions also affect turn-off.
Does AC voltage crossing zero guarantee SCR turn-off?
No. The actual SCR current must fall sufficiently, and the device must recover before forward voltage is reapplied. Load behavior can make current and voltage zero crossings occur at different times.
Can dv/dt be used as the turn-off time for MCR100-8(LS)?
No. Static dv/dt concerns unwanted triggering from a rising blocking-state voltage. The cited MCR100-8(LS) datasheet does not specify tq, and dv/dt is not a substitute.
