PCB Leakage Current: How to Budget and Diagnose High-Impedance Nodes

Estimate leakage error from a node's source impedance, then investigate possible board, component and measurement paths with controlled comparisons.

Small leakage currents can cause measurable errors at high-impedance nodes. A battery divider that drifts in humidity or a sensor amplifier with an unexpected offset may have a board leakage path, but components, connectors, cables, fixtures and instruments can produce similar symptoms. Start with the circuit's allowable error, then use controlled comparisons to narrow down the cause.

The relevant resistance is the resistance of a particular path between conductors, not a universal value for clean or contaminated FR-4. Geometry, surface condition, voltage, temperature, humidity and measurement time can all matter. A useful budget therefore states the circuit model and test conditions rather than assigning a single pass/fail number to a board material.

1. Identify the Possible Paths

Possible path What to investigate Factors to record
Board surface Residue, handling contamination, dust and moisture between conductors Spacing, surface geometry, handling and humidity
Laminate or interfaces Conduction through material or along interfaces near copper and holes Stackup, spacing, material, temperature and moisture exposure
Solder mask or coating region Surface or interface paths affected by the construction and its condition Mask and coating geometry, process and inspection history
Electrochemical migration Possible conductive growth under suitable contamination, moisture and bias Bias, exposure, time and inspection evidence
Components, connectors and cables Package, socket or insulation leakage, device bias current and external paths Part, connection, temperature, fixture and cable condition

Humidity sensitivity is a reason to investigate, not proof of a surface path. Changes in temperature, handling or measurement setup can also change the result.

2. Set a Leakage Budget

For a linear resistive node approximated by a Thevenin source resistance Rs, an independent small leakage current Ileak produces an approximate voltage error:

|Verr| ≈ |Ileak| Rs

For a 1 mV allocation, the following examples use the equivalent source resistance seen at the node, not necessarily the value of a single resistor. They allocate the entire 1 mV to this one current; a real design must share its error budget with other sources.

Assumed source resistance Illustrative current for 1 mV error Resistance for a fixed 5 V across the leakage path
10 kΩ 100 nA 50 MΩ
1 MΩ 1 nA 5 GΩ
5 MΩ 200 pA 25 GΩ
10 MΩ 100 pA 50 GΩ
1 GΩ 1 pA 5 TΩ

The last column is simply R = V/I with an assumed fixed 5 V across the leakage path. A neighboring 5 V rail does not automatically put 5 V across that path: subtract the actual node voltage and account for loading. For a resistive leak that changes the node voltage, solve the loaded circuit; for a TIA or a dynamic, nonlinear or feedback-controlled node, use its appropriate circuit model instead. These values are examples, not board acceptance limits.

3. Worked Examples

Battery-divider loading

Consider an ideal 4.2 V source and two 10 MΩ resistors in series. The unloaded midpoint is 2.10 V, and its Thevenin resistance is 10 MΩ in parallel with 10 MΩ, or 5 MΩ. Ignoring other loads, add an assumed resistance from the midpoint to ground:

Assumed leakage resistance Calculated midpoint Error relative to 2.10 V
No added leakage path 2.1000 V 0%
1 GΩ 2.0896 V −0.50%
100 MΩ 2.0000 V −4.76%

These are hypothetical resistors used to show circuit sensitivity; they are not measured values for clean or contaminated boards. A voltage error cannot be converted into battery capacity error without the cell characteristics and the fuel-gauge model. Tolerances, ADC input behavior and switching also need their own budget.

Transimpedance amplifier

In an ideal transimpedance amplifier with a 1 GΩ feedback resistor, an additional 50 pA input current produces a 50 mV output change in magnitude. Its sign depends on current direction and circuit configuration. This illustration assumes linear operation and excludes amplifier bias current, offset, temperature effects and feedback-network limitations; it is not a measured system result.

4. Match Controls to the Circuit

Design or process question Options to evaluate Confirm with
Can another conductor drive leakage into the node? Increase separation or reduce the length of adjacent conductors; check the resulting circuit and layout Designer
Is a guard useful? Consider a guard at a suitable potential and evaluate its geometry, drive, surface and the complete circuit Designer and component documentation
Could assembly residues affect the node? Assess the flux, assembly process, cleaning compatibility and an appropriate verification method Designer and assembler
Will the environment affect the assembly? Evaluate enclosure, moisture control or a compatible coating with the intended process and exposure Designer and assembler
Is an extreme high-impedance input required? Evaluate insulation, standoffs or an off-board connection together with mechanical, electrical and handling constraints Designer
Is insulation performance a release requirement? Define representative specimens, environmental exposure, bias, measurement method and acceptance criteria Designer, manufacturer and quality team

The TI LMC6032/LMC6034 data sheet, SNOS609D, section 6.4.3, illustrates guard rings for its amplifier configurations. It describes a guard held near input potential and notes that a grounded guard can still offer some protection when both inputs are active and high impedance. These are device-specific examples, not a universal guard recipe. Our PCB guard-trace guide discusses guarding alongside other layout concerns.

Coating over residue does not automatically eliminate its effects; coating, cleaning and material compatibility should be evaluated together. CTI characterizes resistance to surface tracking under its specified test conditions; it is not a direct measurement of a particular low-voltage circuit's leakage current. Consult the cleanliness testing guide and no-clean flux guide for related process decisions.

5. Diagnose with Controlled Comparisons

Observation Hypothesis to investigate Useful comparison
Error changes after humidity exposure Surface or interface conduction, or humidity-sensitive components and fixtures Compare controlled exposures with stable temperature and instrument setup; include controls
Error changes after cleaning and drying Residue or moisture may contribute Compare compatible treatment and untreated controls, handling, drying and repeat measurements
Error changes with voltage or time under bias Leakage or other voltage- and time-dependent mechanisms may contribute Record the voltage across the suspected path and compare conditions under an approved test plan
Error changes with temperature Device, material, connector or instrument effects may contribute Compare components, fixture and board under controlled conditions
A bare-board path measures differently from an assembly Assembly, component or fixture contributions may differ Use representative matched samples and the same specified method; do not treat bare-board results as the assembled system

Before testing, a qualified project team should define safe de-energization and isolation, permitted test voltage, component and material limits, solvent and drying compatibility, exposure and settling times, handling, guarding, instrument leakage floor and acceptance criteria. Compare repeat measurements and suitable controls; an insulation-resistance test on a populated circuit can stress components or measure unintended parallel paths. A visual residue or a change after treatment is evidence to investigate, not by itself proof of a failure mechanism.

6. Handoff and RFQ Checklist

  1. Mark sensitive nodes and their revision-controlled circuit and layout data.
  2. State the operating conditions, error allocation, source impedance or applicable circuit model, and expected neighboring potentials.
  3. Document the intended guard and any local mask requirements for fabrication and assembly review.
  4. Identify compatible flux, cleaning or coating requirements where needed; agree on verification rather than assuming a universal process.
  5. Define representative board, assembly and fixture controls, test conditions, measurement limits and acceptance criteria.
  6. Agree on test ownership, sampling and required records before release.

For assembly planning, share the relevant drawings and requirements with HILPCB PCB assembly or SMT assembly through the quote page. Confirm the available cleaning, coating, test and reporting scope for the particular build. For a separate discussion of spacing and conductive anodic filament risks, see the hole-to-hole spacing guide.

FAQ

What causes leakage current on a PCB?

Possible contributors include board surfaces, materials and interfaces, as well as component packages, connectors, cables and fixtures. Humidity or residue may affect a path, but the cause must be investigated under defined conditions.

How much leakage current is acceptable?

It depends on the circuit and its error budget. For a linear resistive node, divide the voltage-error allocation by the equivalent source resistance. For example, 1 mV divided by 5 MΩ is 200 pA when that entire allocation is assigned to the modeled current.

Does conformal coating stop leakage current?

A suitable coating may help manage environmental exposure, but its effect depends on the coating, surface condition, process and environment. It does not automatically correct contamination or qualify a finished assembly; validate the intended construction.

Does a high CTI laminate guarantee low leakage current?

No. CTI is a tracking test classification under specified conditions, not a direct leakage-current specification for the actual circuit. Evaluate the material and finished construction against the project's operating and test conditions.

How do I investigate a suspected leakage path?

Define the circuit model and compare controlled measurements across board, component and fixture hypotheses. A qualified test plan should cover isolation, permitted voltage, compatible handling and treatment, environmental conditions, instrument limits and acceptance criteria.